| The Black and White of Immersion Tin |
 |
 |
| Written by Allan Wilcox | |||
| Wednesday, 01 July 2009 23:39 | |||
Keeping an eye on cupric ions can eliminate black tin.Every immersion tin plating operation faces the same problem during the immersion tin bath. Eventually, the bath will begin to plate black tin, and until recently, there has been no way to predict when the bath would begin to plate black tin. You might ask, “Why does this happen?”When immersion tin plates onto the copper, two atoms of copper dissolve for every atom of tin that plates out. The copper metal goes into solution as copper one (also known as cuprous ions, or Cu+). Copper in this form is well tolerated by most immersion tin plating solutions, and at reasonable levels, it has no effect. However, cuprous ions can react with atmospheric oxygen. When this happens, it is converted to copper two (cupric ions or Cu+2). This is the form of copper found in most electroplating baths, and it is blue in color. Cupric ions react with tin metal causing the copper to plate out. This copper plating out onto the tin is the black deposit that can appear on the top of the tin, often referred to as black tin. Enter a new spectrophotometric method to measure cupric ions in any immersion tin solution. In theory, you could actually use your eye to estimate color as an indication of cupric ion build up, but a spectrophotometer will give you an exact reading. To predict when the tin bath will plate black, measure the cupric level in the bath just when plating starts to darken and use this measure of Cu+2 in your tin bath to predict when it is time for a new bath. The maximum amount of cupric ion that your tin bath can tolerate is a function of specific bath chemistry, and it varies with different chemical suppliers. If an absolute standard is desired, 1000 ppm of copper can be achieved by adding 15 mls of standard copper sulfate solution to a liter of a fresh tin bath. This measure should be done carefully, as cuprous ions in the bath sample can change rapidly to cupric ions; thus, conditions used by the method are designed to slow conversion of cuprous to cupric during the test. Some tin baths with an extremely high tolerance to cupric ions have been known to reach as high as 1400 ppm (1.4 grams/liter) of copper before the plating darkens. Method BackgroundIn order to understand the Zincon – Cupric Method, it is useful to discuss the science behind spectrophotometric methods. The critical detail is that spectrophotometric methods measure of the amount of a specific metal ion in a solution, based on the ability of a dye to form a complex with the metal ion of interest and causing a change in color of the dye.The Zincon-Cupric Method uses Zincon to selectively form a complex with the cupric ions. Whereas cupric ions form a stable, bright blue complex with Zincon, cuprous ions and tin ions do not form a complex with Zincon. The selectivity of Zincon for cupric ions and change in color is only part of what makes this method possible. The amount of light absorbed by a solution is directly proportional to the amount of material in solution. So, as the amount of cupric ions increases in solutions of Zincon, more Zincon-Cupric complex is formed, and the solution color changes from orange-red to bright blue (FIGURE 1).  The properties of Zincon provide a method to measure how much cupric ion there is in an immersion tin solution. The method uses a spectrophotometer to measure how much light is absorbed at a specific wavelength of light. Zincon-Cupric Method SpecificsThe spectrum of uncomplexed Zincon in the indicator solution used in the Zincon-Cupric Method is shown in FIGURE 2 (red line). In the absence of cupric ion, the wavelength of maximum absorbance by Zincon is 490 nanometers (nm). When an immersion tin solution is doped with cupric ions and the bath analyzed by the method, the complex formed between Zincon and cupric ions absorb most strongly at 605 nm (Figure 2, blue line). The maximum allowable amount of cupric ion in an immersions tin solution can be measured and specified by the Zincon-Cupric Method. The method is very simple, consisting of adding a sample of the bath to an indicator solution, and measuring the absorbance at 605 nm with a spectrophotometer. Procedure1. Prepare the Zincon-Cupric Indicator Solution (1.0 Liter). To approximately 500 mls of deionized water add:100 mls Cupric Inhibitor* 100 mls Zincon Indicator concentrate** 2. Add a sample (1.0 mL) of the tin bath to the indicator solution. 3. Adjust pH to 10.4 with concentrated ammonia, then dilute to 1.0 liter with deionized water. 4. Allow solution to sit for 20 minutes for reaction to complete. 5. Read the absorbance at 605 nm by a spectrophotometer. *The Cupric Inhibitor contains Thiourea (76 g/L) and Sodium Bisulfite (10 g/L) in deionized water. **The Zincon Indicator Concentrate is 0.23 grams per liter Zincon indicator dissolved in 400 grams/liter Triethanolamine solution. Note: For those attempting to make their own reagents, be aware. Conventional commercial Triethanolamine is actually 80% Triethanolamine + 20% Diethanolamine. The presence of Diethanolamine causes the Zincon indicator to become unstable. We are using a special grade of pure Triethanolamine available, commercially diluted to 85% with water. CalculationsIn the absolute sense, no calculations are necessary to monitor the build up of cupric ions with the Zincon-Cupric Method. Simply recording the absorbance at 605 nm is sufficient to establish the Zincon-Cupric Method for specific bath conditions. The maximum absorbance limit is obtained when the bath begins to plate out black tin.ConclusionsWe have described a convenient method useful for measuring the amount of cupric in a tin bath. The method is very simple to implement and involves adding a sample of the tin bath to an indicator solution and then measuring the absorbance with a spectrophotometer. PCD&FAllan Wilcox is the technical service chemist with RD Chemical Company, Inc.; This e-mail address is being protected from spambots. You need JavaScript enabled to view it .
|
Design News
- Cadence Swings to Q4 Profit
- Cadence Latest to Sign on for Virtual PCB
- Zuken to Exhibit at Virtual PCB
- Altium, EMA to Exhibit at Virtual PCB
- Altium Adds York to University Partners List
- Cadence to Lay Off 120 Workers
- SMTA Named Exclusive Sponsor of Virtual PCB
- NI Creates Grant Program to Support Texas Emerging Technology Fund
- NI Names AMD CTO to Head R&D
- Meptec Finalizes EDA Challenges Symposium
Market News
- Virtual PCB Technical Conference Emerging
- PCB Orders Up 22% in December
- 2009 Semi Sales Slipped 9%
- EDA Q3 2009 Revenue Up Nearly 4% Sequentially
- Global Telecom Service Revenues to Reach $3.7T by 2015
- UP Media Group Issues Call for Papers for PCB West 2010
- Report: Tech Sector to Recover in 2010
- '6 Straight': Component Orders Up Again
- iSuppli: Consumer Electronics Q3 Revenues Up 11% Sequentially
- Consumer Product Safety Commission to Rule on Lead in Electronics
Fab News
- Merix, Viasystems Merger Approved
- Thai Bank to Innovex: Pay Up
- M-Flex Records Record Sales
- TTM Swings to Q4 Profit
- Firan Reports 24% Q4 Sales Drop
- TTM Gets Security OK for Meadville Acquisition
- Printed Circuits Adds Buried Passives Technology
- Nanya Parent May Spend $1B for Capacity Expansion
- Molex Flex Circuit Arm's Sales Dip
- Park Makes Changes to Marketing Group
Products
Grieve Introduces No. 952 Oven
No. 952 is a 550°F electrically-heated forced air convection bench oven, currently used for various programmed heat processings. Workspace dimensions measure 26" x 22" x 16". 3kW installed in Incoloy-sheathed tubular elements provide heat to the workload. A 1/80-HP recirculating blower creates a convection air movement in the chamber. Features 3" insulated walls, an aluminized steel exterior, Type 430 stainless steel interior and an integral oven stand. Has a programmable and recording temperature controller with 10" diameter circular chart, plus a manual reset excess temperature controller...
No. 952 is a 550°F electrically-heated forced air convection bench oven, currently used for various programmed heat processings. Workspace dimensions measure 26" x 22" x 16". 3kW installed in Incoloy-sheathed tubular elements provide heat to the workload. A 1/80-HP recirculating blower creates a convection air movement in the chamber. Features 3" insulated walls, an aluminized steel exterior, Type 430 stainless steel interior and an integral oven stand. Has a programmable and recording temperature controller with 10" diameter circular chart, plus a manual reset excess temperature controller...
Sponsor Links
Low Cost PCB Prototypes
PCB-POOL® manufactures high quality PCB prototypes at exceptional prices!
Receive instant quotes (no registration required) and order your PCBs directly online.
Special Offer: Free Laser SMD stencil with all prototype orders!
Need PCB prototypes fast?
Sunstone Circuits takes the pain out of prototyping! We are dedicated to making the online ordering of PCB prototypes simple, fast, and easy from quote to delivery. Quick access to our 24/7/365 customer service team and easy online order tracking takes the pain out of sourcing prototypes online.
Put us to the test - order Sunstone Circuits today!
Search
Search
Login
CB Login
Language
Language
Features
Improving Fabrication Yields
How the CAM engineer can make the difference. Embedded in fabrication planning is calculating panel size, checking layer stackup information, reviewing expected yields, reviewing board construction and verifying impedance control calculations. Typical panel sizes are 9 x 12˝, 12 x 18˝, 18 x 24˝, or 18 x 36˝. A number of factors need to be considered when calculating panel size. For instance, consider a small board of 25 sq. in. A relatively high number of this small board can be panelized...
How the CAM engineer can make the difference. Embedded in fabrication planning is calculating panel size, checking layer stackup information, reviewing expected yields, reviewing board construction and verifying impedance control calculations. Typical panel sizes are 9 x 12˝, 12 x 18˝, 18 x 24˝, or 18 x 36˝. A number of factors need to be considered when calculating panel size. For instance, consider a small board of 25 sq. in. A relatively high number of this small board can be panelized...
Current Issue
Parts
Printed Circuit Design & Fab Magazine on Facebook